best free templates

- Product
Q1

Product details :

 

 

 

 

 

 

4.1 REPLACEMENT OF WELDING FILTER LENS,
PROTECTION PLATE AND SAFETY PLATE

 

 

 

 

 

 

 

 

 

Replacement of welding filter lens and front-mounted protection
plate:
-lift up hatch of welding filter lens.
-(1) Release filter retaining spring with finger from hatch slot.
-(2) Remove welding filter lens (and eventual protection plate).
-Mount new welding filter lens (and eventual protection plate)
to its place..
-Press filter retaining spring into the slot, in which case it is
locked at its place.
-(3)Front-mounted protection plate is removed by drawing it
outwards.
-Replacement of the inner safety plate, attached to the welding
helmet:
-Lift up hatch of welding filter lens.
-(4)Press safety plate out of its place.
Mount new safety plate by bending it so that its ends slide
between the cogging in the helmet. Release the plate at its place
by unbending it. Make sure that the plate is fully in the slot.4.2 USE OF VIEWING POSITION OF WELDING HELMET
HATCH
The welding filter lens hatch has an intermediate position to
make welding start or e.g. short tack welds easier.
NOTE! Through the slit you can check the start point before
starting but you should adjust the welding helmet before arc
ignition such a way that the igniting arc can be seen through the
welding filter lens.
We recommend that the viewing position is used only temporarily
and with low welding currents. At higher currents the
radiation coming through the hatch openings may burn the skin
and reduce vision through the welding filter lens.
Never use the viewing position with auto darkening welding
filter. Diffused light hinders normal function of the filter.
Never watch the arc through the slit!
4.3 ADJUSTMENTS
Height adjustment of band:
Adjust the headband height so that the band part circling the
head positioned relatively low, in which case the welding helmet
stays rigidly positioned on the head.
counterpart (D).Adjust the upper part of band to the desired
length by moving plastic strips in regard to each other. Press
the plastic strips against each other so that the plastic pins are
placed into holes of counterpart.
Tightening adjustment of band:
Adjust the band tightness suitable for your head by rotating
the adjusting wheel (G).
Adjustment of welding helmet angle:
Adjust the welding helmet angle in regard to your face so that
the lower edge of welding helmet is positioned near your chest
in the welding situation, in which case the welding helmet gives
the best protection. Bend the adjustment plate (A) inwards so
much that the plastic pin(B) of the welding helmet comes out
of the hole of the adjustment plate. Turn the adjustment plate
and release the plate so that the screw is placed to the desired
hole of the adjustment plate.Tightening adjustment of welding helmet:
Adjust the tightness of welding helmet in regard to band by
rotating the screw (E) and (F), adjust the tightness of helmet so
that the high raised helmet stays up, but goes down when you
nod your head. If the helmet strikes against your chest when
failing, the adjustment is too loose or the helmet angle has been
adjusted too near your face from the adjustment plate (A)

 

 

 

 

 

 

 

 

 

 

 

 

MEANING OF THE MARKING PRESENT ON
THE HELMET 5

Identification of the manufacturer: LQ
Number of the European Standard on whom the helmet is in
compliance: EN 175
Field of use: Mechanical Strenght - Increased Robustness í░Sí▒
CE : marking of the European Conformity
7
immediately.
-Never use a damaged welding helmet or a welding helmet with
defective or insufficient equipment!
-Before use always inspect the condition of welding filter lens,
protection plate and plastic safety plate and that these have
been mounted in the right way:
-Inspect that the front-mounted protection plate and inner
plastic safety plate are undamaged, or if spatter or scratches
reduce vision. Dirty protection glass may hinder normal function
of the auto darkening welding filter.
-Inspect that the welding filter lens, damaged welding filter
lens impairs protection. Therefore it should be replaced
immediately. Make sure that the degree of protection of welding
filter lens is appropriate for your work. Inspect that the
welding helmet and headband are undamaged. Inspect that the
hatch of the welding helmet is completely closed when in
down position.
Careful use and safe keeping of welding helmet make its operation
life longer and improve your safety!
-Do not put the welding helmet on hot surface, e.g. on hot
welding seam!
6.1 CLEANING
Clean the welding helmet with damp cleaning cloth which is
watered with mild soap water. To clean the auto darkening
welding filter, first remove the filter from its place as described
in paragraph 4.1
Do not use any dissolvent for cleaning the welding helmet.
Do not wipe the plastic safety plates e.g with gloves because
they are easily scratched.
INSTRUCTIONS FOR THE USE OF THE
AUTO DARKENING WELDING FILTER

Auto darkening welding filter is delivered ready for use. Make
sure that the filter is mounted to the hatch so that the photocell
is directed towards the work piece.
HAIJING adjusts the shade of the panel according to the
welding method and current used. Adjust the sensitivity as
needed.
The photocells and light detectors of the filter should always
be kept clean. Clean them with soft cleaning cloth which is
moistened with mild soap water (or alcohol).
The operation temperature range of the filter is -50C...+550C.
Do not cover the photocells or light detectors! Inspect that
the protection plate is not dirty so that it hinders the filterí»s
function.
Do not immerse in liquid!
Do not try to open the filter!
Protect from heat and direct sunlight.
Store at dark and keep dry room temperature.

 

 

 

 

 

 

 

TECHNICAL DATA 8
Manufacturer: HaiJing (Changzhou)Technology Co., Ltd
(hereinafter referred as HaiJing)
Size of welding filter lens: 110x90mm
Degrees of protection of welding filter lenses DIN 9-13
Operation temperature range: -50C-/ +550C
Auto darkening welding filter:-50C-/ +550C

Storage temperature range: -400C-/ +700C
Auto darkening welding filter: -50C-/ +550C
Welding helmet material: PA/6
Weight: 550g
CE-marking:
The product has been type inspected by Haijing (Changzhou)
Technology Co.,Ltd 

TERMS OF GUARANTEE 9
Liquinz gives the auto darkening welding filter of HAIJING welding helmets a guarantee of 2 years, provided that the
helmet is used for single operation.
or indirect travel expenses caused by guarantee repair, or
direct or indirect damages caused by defective product.
Guarantee defects must be informed to Haijing , Part replaced
under the terms of guarantee remains the property of Haijing
and is to be returned to Haijing.

WARNING 10
The materials which may come into contact with the wearerí»s
skin could cause allergic reaction to susceptible individuals.
Toughened mineral filter oculars shall only be used in conjunction
with a suitable backing ocular.